Why does my trolling motor have 4 wires?
Attach one set of red and black wires to one battery’s positive and negative poles and the other set to the other battery or battery setup. Trolling motors with four wires usually have switches that allow you to choose which battery setup to use.
What size wire is on a Minn Kota trolling motor?
CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE
| MOTOR THRUST/MODEL | MAX AMP DRAW | WIRE EXTENSION LENGTH |
|---|---|---|
| 5 FT | ||
| 30 lb. | 30 | 10 AWG |
| 40 lb., 45 lb. | 42 | 10 AWG |
| 50 lb., 55 lb. | 50 | 8 AWG |
Do I need a fuse for my Minn Kota trolling motor?
It is highly recommended that a circuit breaker or fuse be used when installing a trolling motor. Refer to the Minn Kota “Conductor Gauge and Circuit Breaker Sizing Table”.
What size wire do I need to run a trolling motor?
Always keep in mind that you’ll need an 8-gauge wire for a 50-amp trolling motor and a 6-gauge one for its 60-amp counterpart. I can say the same if you’re wiring a fuse for a 12V trolling motor, which, incidentally, is almost always more economical than a breaker.
Can you run a trolling motor without a circuit breaker?
Yes, you must install a circuit breaker when using a trolling motor, even though the battery would power the motor without it as well. There are several reasons. First, trolling motor manufacturers require the use of circuit breakers. Not using one will void your warranty.
Do I need an inline fuse for my trolling motor?
Inline fuses are the most popular type used with trolling motors.
How do you wire a 24 volt trolling motor plug?
Feed the wires through the plug housing. On the 12-24V trolling motor plug, connect the positive 24V wire to the terminal marked “24”, the 12V wire to the terminal marked “12” and the negative wire to the terminal marked “-”. On straight 24V trolling motors, connect the two wires to “24” and “-” as appropriate.
What size wire do you use for a 12 volt trolling motor?
How many amps does a Minn Kota draw?
The Minn Kota Endura C2 55 Transom – mount 12V 55 lb. Thrust Trolling Motor has a max amp draw of 52 amps/hr but only 5 lbs more thrust.
What gauge wire is on a trolling motor?
Many trolling motors can be used with 8 gauge wire, however, the length of wire you need and the amperage of your motor can alter the size of wire you need. For example, if you need a longer length of wire, you’ll likely need a lower gauge and therefore thicker wire.
Is the Minn Kota trolling motor wiring diagram WEEE compliant?
The following Motor Wiring Diagram applies to all PowerDrive models that do not . The parts diagram and parts list provides Minn Kota® WEEE compliance. We have the factory trained techs to fix your Minn Kota trolling motor.
What size circuit breaker do I need for my Minn Kota motor?
Refer to the Minn Kota “Conductor Gauge and Circuit Breaker Sizing Table”. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended. Batteries should be stored and maintained at full charge.
What kind of Electrical Connections do I need for my trolling motor?
Includes information on conductor gauge and circuit breaker size, battery type, run time, and 12v, 24v, or 36v connections. Diagrams outlining the accessories and cables required to connect a trolling motor to a 12v, 24v, 36v, or 48v system. Learn how to pair an i-Pilot, i-Pilot Link, CoPilot or Micro Remote to your trolling motor.